Malays. J. Anal. Sci. Volume 30 Number 5 (2026): 1887

 

Research Article

Response surface methodology assisted electrochemical sensor for the detection of 3-MCPD

Mohd Zaheer Khan Mohd Ali1, Wan Jefrey Basirun2, Zainiharyati Mohd Zain3, Siti Nor Atika Baharin1, Mohd Azerulazree Jamilan4, and Kavirajaa Pandian Sambasevam1,3*

1Advanced Materials for Environmental Remediation (AMER), Faculty of Applied Sciences, Universiti Teknologi MARA, Cawangan Negeri Sembilan, Kampus Kuala Pilah, 72000, Kuala Pilah, Negeri Sembilan, Malaysia

2Department of Chemistry, Faculty of Science, Universiti Malaya, 50603, Kuala Lumpur, Malaysia.

3Electrochemical Material and Sensor (EMaS) Research Group, Universiti Teknologi MARA, Shah Alam, 40450 Selangor Malaysia

4 Nutrition Unit, Nutrition, Metabolism and Cardiovascular Research Centre (NMCRC), Institute for Medical Research, National Institute of Health, Ministry of Health Malaysia, No. 1, Jalan Setia Murni U13/52, Setia Alam, 40170 Shah Alam, Selangor D.E., Malaysia

 

*Corresponding author: kavirajaa@uitm.edu.my

 

Received: 1 April 2026; Revised: 12 June 2026; Accepted: 24 June 2026; Published: 31 October 2026

Abstract

3-MCPD (3-monochloropropane-1,2-diol) is a chemical contaminant formed during high-heat food processing. It is mostly found in refined vegetable oils (especially palm oil) and soy sauce. It is a suspected human carcinogen and has been linked to kidney damage. Because of these severe health risks, global food safety authorities strictly regulate and monitor its levels to ensure public safety. A molecularly imprinted polypyrrole/chitosan (MIPPy/CHT) electrochemical sensor was fabricated via electropolymerization for the selective detection of 3-monochloropropane-1,2-diol (3-MCPD). The surface morphology and elemental composition were characterized using field emission scanning electron microscopy (FESEM) coupled with energy-dispersive X-ray spectroscopy (EDX), while electrochemical techniques were employed to evaluate interfacial behavior and sensing performance. Fabrication parameters were systematically optimized using Response Surface Methodology (RSM). A two-level factorial design identified pH, number of scans, starting potential, and elution time as influential factors, with pronounced quadratic effects observed for pH, scan number, and starting potential. Mildly acidic conditions (pH 4) enhanced hydrogen-bonding interactions, while excessive number of scans and higher starting potentials for sensor fabrication reduced sensor response(A). Subsequent optimization using a Box–Behnken design (BBD) established optimal conditions at pH 4, 3 electropolymerization scans, lower electropolymerization starting potential at 0V, and 15 min elution time. Significant interaction effects were observed between pH and scan number, as well as between scan number and starting potential, confirming the critical balance between polymer growth and cavity accessibility. Under optimized conditions, the sensor exhibited a linear response toward 3-MCPD over 100–500 nM with a high correlation coefficient (R˛ = 0.9963). The limit of detection (LOD) and limit of quantification (LOQ) were 36 nM and 111 nM, respectively. These results demonstrate that the MIPPy/CHT sensor provides high sensitivity, good selectivity, and reliable analytical performance for 3-MCPD detection.

Keywords: 3-monochloropropane-1,2-diol, molecularly imprinted polymer, polypyrrole/chitosan composite, electrochemical sensor, response surface methodology


References

1.        Sulin, S., Mokhtar, M., Mohammed, M., & Baharuddin, A. (2020). Review on palm oil contaminants related to 3-monochloropropane-1, 2-diol (3-MCPD) and glycidyl esters (GE). Food Research, 4(S6), 11-18.

2.        Buhrke, T., Schultrich, K., Braeuning, A., & Lampen, A. (2017). Comparative analysis of transcriptomic responses to repeated-dose exposure to 2-MCPD and 3-MCPD in rat kidney, liver and testis. Food and Chemical Toxicology, 106, 36-46.

3.        Eisenreich, A., Monien, B. H., Götz, M. E., Buhrke, T., Oberemm, A., Schultrich, K., Abraham, K., Braeuning, A., & Schäfer, B. (2023). 3-MCPD as contaminant in processed foods: State of knowledge and remaining challenges. Food Chemistry, 403, 134332.

4.        Chain, E. Panel o. C. i. t. F. (2016). Risks for human health related to the presence of 3- and 2-monochloropropanediol (MCPD), and their fatty acid esters, and glycidyl fatty acid esters in food. EFSA Journal, 14(5), e04426.

5.        Wong, K. O., Cheong, Y. H., & Seah, H. L. (2006). 3-Monochloropropane-1,2-diol (3-MCPD) in soy and oyster sauces: Occurrence and dietary intake assessment. Food Control, 17(5), 408-413.

6.        Baer, I., De la Calle, B., & Taylor, P. (2010). 3-MCPD in food other than soy sauce or hydrolysed vegetable protein (HVP). Analytical and Bioanalytical Chemistry, 396(1), 443-456.

7.        Parisi, O. I., Francomano, F., Dattilo, M., Patitucci, F., Prete, S., Amone, F., & Puoci, F. (2022). The Evolution of Molecular Recognition: From Antibodies to Molecularly Imprinted Polymers (MIPs) as Artificial Counterpart. Journal of Functional Biomaterials, 13(1), 12. 2079-4983.

8.        Sun, X., Zhang, L., Zhang, H., Qian, H., Zhang, Y., Tang, L., & Li, Z. (2014). Development and application of 3-chloro-1,2-propandiol electrochemical sensor based on a polyaminothiophenol modified molecularly imprinted film. Journal of Agricultural and Food Chemistry, 62(20), 4552-4557.

9.        Martin, A. A., Fodjo, E. K., Eric-Simon, Z. V., Gu, Z., Yang, G., Albert, T., Kong, C., & Wang, H.-F. (2021). Cys-AgNPs modified gold electrode as an ultrasensitive electrochemical sensor for the detection of 3-chloropropane-1,2-diol. Arabian Journal of Chemistry, 14(9), 103319.

10.     Cheng, W., Zhang, Q., Wu, D., Yang, Y., Zhang, Y., & Tang, X. (2022). A facile electrochemical method for rapid determination of 3-chloropropane-1,2-diol in soy sauce based on nanoporous gold capped with molecularly imprinted polymer. Food Control, 134, 108750.

11.     Chi, H., Li, Y., & Liu, G. (2022). Molecularly imprinted sensing platform based on electrochemically modified graphite paper for efficient detection of 3-monochloropropane-1,2-diol. Food Chemistry, 386, 132829.

12.     Yaman, Y. T., Bolat, G., Saygin, T. B., & Abaci, S. (2021). Molecularly imprinted label-free sensor platform for impedimetric detection of 3-monochloropropane-1,2˗diol. Sensors and Actuators B: Chemical, 328, 128986.

13.     Pang, A. L., Arsad, A., & Ahmadipour, M. (2021). Synthesis and factor affecting on the conductivity of polypyrrole: a short review. Polymers for Advanced Technologies, 32(4), 1428-1454.

14.     Deng, F., Li, Y., Luo, X., Yang, L., & Tu, X. (2012). Preparation of conductive polypyrrole/TiO2 nanocomposite via surface molecular imprinting technique and its photocatalytic activity under simulated solar light irradiation. Colloids and Surfaces A: Physicochemical and Engineering Aspects, 395, 183-189.

15.     Xu, L., Huang, Y.-A., Zhu, Q.-J., & Ye, C. (2015). Chitosan in Molecularly-Imprinted Polymers: Current and Future Prospects. International Journal of Molecular Sciences, 16(8), 18328-18347.

16.     Sambasevam, K. P., Sateria, S. F., Baharin, S. N. A., Azman, N. J., Ahmad Wakid, S., & Shahabuddin, S. (2023). An optimization of fungal chitin grafted polyaniline for ammonia gas detection via Box Behnken design. International Journal of Biological Macromolecules, 238, 124079.

17.     Ferreira, S. L. C., Bruns, R. E., Ferreira, H. S., Matos, G. D., David, J. M., Brandăo, G. C., da Silva, E. G. P., Portugal, L. A., dos Reis, P. S., Souza, A. S., & dos Santos, W. N. L. (2007). Box-Behnken design: An alternative for the optimization of analytical methods. Analytica Chimica Acta, 597(2), 179-186.

18.     Fang, M., Zhou, L., Zhang, H., Liu, L., & Gong, Z.-Y. (2019). A molecularly imprinted polymers/carbon dots-grafted paper sensor for 3-monochloropropane-1,2-diol determination. Food Chemistry, 274, 156-161.

19.     Xing, X., & Cao, Y. (2007). Determination of 3-chloro-1,2-propanediol in soy sauces by capillary electrophoresis with electrochemical detection. Food Control, 18(2), 167-172.

20.     Geng, X., Kwon, O.-H., & Jang, J. (2005). Electrospinning of chitosan dissolved in concentrated acetic acid solution. Biomaterials, 26(27), 5427-5432.

21.     Albar, M. M. J., Jamion, N. A., Baharin, S. N. A., Raoov, M., & Sambasevam, K. P. (2020). Preparation of novel commercial polyaniline composites for ammonia detection. Solid State Phenomena, 301, 124-131.

22.     Yang, Y., Fang, G., Wang, X., Pan, M., Qian, H., Liu, H., & Wang, S. (2014). Sensitive and selective electrochemical determination of quinoxaline-2-carboxylic acid based on bilayer of novel poly(pyrrole) functional composite using one-step electro-polymerization and molecularly imprinted poly(o-phenylenediamine). Analytica Chimica Acta, 806, 136-143.

23.     Bougrini, M., Florea, A., Cristea, C., Sandulescu, R., Vocanson, F., Errachid, A., Bouchikhi, B., El Bari, N., & Jaffrezic-Renault, N. (2016). Development of a novel sensitive molecularly imprinted polymer sensor based on electropolymerization of a microporous-metal-organic framework for tetracycline detection in honey. Food Control, 59, 424-429.

24.     Pfaff, T. J. (2023). Formulas Quantifying Change. In T. J. Pfaff (Ed.), Applied Calculus with R (pp. 65-76). Springer International Publishing.

25.     Ahmed, R. K., Saad, E. M., Fahmy, H. M., & El Nashar, R. M. (2022). Multivariate experimental design: towards more reliable electrochemical detection. Current Opinion in Electrochemistry, 31, 100880.

26.     Ling, T.-R., Hsieh, W.-C., Li, Y.-Y., & Hung, T.-T. (2023). MIP sensor made using multi-current step electro-polymerization method on framed Ag-SPE for glutamic acid enantiomer recognition. Journal of Electroanalytical Chemistry, 944, 117635.

27.     Zembrzuska, D., Kalecki, J., Cieplak, M., Lisowski, W., Borowicz, P., Noworyta, K., & Sharma, P. S. (2019). Electrochemically initiated co-polymerization of monomers of different oxidation potentials for molecular imprinting of electroactive analyte. Sensors and Actuators B: Chemical, 298, 126884.

28.     Wu, Y., Li, G., Tian, Y., Feng, J., Xiao, J., Liu, J., Liu, X., & He, Q. (2021). Electropolymerization of molecularly imprinted polypyrrole film on multiwalled carbon nanotube surface for highly selective and stable determination of carcinogenic amaranth. Journal of Electroanalytical Chemistry, 895, 115494.

29.     Di Masi, S., De Benedetto, G. E., & Malitesta, C. (2024). Optimisation of electrochemical sensors based on molecularly imprinted polymers: from OFAT to machine learning. Analytical and Bioanalytical Chemistry, 416(9), 2261-2275.

30.     Szpisják-Gulyás, N., Al-Tayawi, A. N., Horváth, Z. H., László, Z., Kertész, S., & Hodúr, C. (2023). Methods for experimental design, central composite design and the Box–Behnken design, to optimise operational parameters: A review. Acta Alimentaria, 52(4), 521-537.

31.     Martin, A. A., Fodjo, E. K., Marc, G. B. I., Albert, T., & Kong, C. (2021). Simple and rapid detection of free 3-monochloropropane-1,2-diol based on cysteine modified silver nanoparticles. Food Chemistry, 338, 127787.

32.     Alizadeh, T., Ganjali, M. R., Zare, M., & Norouzi, P. (2010). Development of a voltammetric sensor based on a molecularly imprinted polymer (MIP) for caffeine measurement. Electrochimica Acta, 55(5), 1568-1574.

33.     da Silva, H., Pacheco, J., Silva, J., Viswanathan, S., & Delerue-Matos, C. (2015). Molecularly imprinted sensor for voltammetric detection of norfloxacin. Sensors and Actuators B: Chemical, 219, 301-307.

34.     Cheng, Z., Wang, E., & Yang, X. (2001). Capacitive detection of glucose using molecularly imprinted polymers. Biosensors and Bioelectronics, 16(3), 179-185.

35.     Akpinar, H., Nurioglu, A. G., & Toppare, L. (2012). Influence of hydrogen bonding on electrochromic properties of conducting polymers. Journal of Electroanalytical Chemistry, 683, 62-69.

36.     Yang, R., Ruan, C., Dai, W., Deng, J., & Kong, J. (1999). Electropolymerization of thionine in neutral aqueous media and H2O2 biosensor based on poly(thionine). Electrochimica Acta, 44(10), 1585-1596.

37.     Tamandani, M., & Hashemi, S. H. (2022). Central Composite Design (CCD) and Box-Behnken Design (BBD) for the Optimization of a Molecularly Imprinted Polymer (MIP) Based Pipette Tip Micro-Solid Phase Extraction (SPE) for the Spectrophotometric Determination of Chlorpyrifos in Food and Juice. Analytical Letters, 55(15), 2394-2408.

38.     Sulaiman, N. S., Hashim, R., Mohamad Amini, M. H., Danish, M., & Sulaiman, O. (2018). Optimization of activated carbon preparation from cassava stem using response surface methodology on surface area and yield. Journal of Cleaner Production, 198, 1422-1430.

39.     Das, S., & Mishra, S. (2017). Box-Behnken statistical design to optimize preparation of activated carbon from Limonia acidissima shell with desirability approach. Journal of Environmental Chemical Engineering, 5(1), 588-600.

40.     Natarajan, E., & Ponnaiah, G. P. (2017). Optimization of process parameters for the decolorization of Reactive Blue 235 dye by barium alginate immobilized iron nanoparticles synthesized from aluminum industry waste. Environmental Nanotechnology, Monitoring & Management, 7, 73-88.

41.     Ghoreishian, S. M., Raju, G. S. R., Pavitra, E., Kwak, C. H., Han, Y.-K., & Huh, Y. S. (2019). Ultrasound-assisted heterogeneous degradation of tetracycline over flower-like rGO/CdWO4 hierarchical structures as robust solar-light-responsive photocatalysts: Optimization, kinetics, and mechanism. Applied Surface Science, 489, 110-122.

42.     Ozkorucuklu, S. P., Sahin, Y., & Alsancak, G. (2008). Voltammetric behaviour of sulfamethoxazole on electropolymerized-molecularly imprinted overoxidized polypyrrole. Sensors, 8(12), 8463-8478.

43.     Zeb, S., Wong, A., Khan, S., Hussain, S., & Sotomayor, M. D. P. T. (2021). Using magnetic nanoparticles/MIP-based electrochemical sensor for quantification of tetracycline in milk samples. Journal of Electroanalytical Chemistry, 900, 115713.

44.     Naskar, H., Ghatak, B., Biswas, S., Singh, P. P., Tudu, B., & Bandyopadhyay, R. (2020). Electrochemical detection of eugenol (EU) using polyacrylonitrile molecular imprinted polymer embedded graphite (PAN-MIP/G) electrode. IEEE Sensors Journal, 20(1), 39-46.

45.     Chatterjee, T. N., Das, D., Roy, R. B., Tudu, B., Sabhapondit, S., Tamuly, P., Pramanik, P., & Bandyopadhyay, R. (2018). Molecular imprinted polymer based electrode for sensing catechin (+C) in green tea. IEEE Sensors Journal, 18(6), 2236-2244.

46.     Yang, S., Wang, Y., Xu, M., He, M., Zhang, M., Ran, D., & Jia, X. (2013). Synthesis of modified chitosan-based molecularly imprinted polymers for adsorptive protein separation. Analytical Methods, 5(20), 5471-5477.

47.     Khoo, W. C., Kamaruzaman, S., Lim, H. N., Jamil, S. N. A. M., & Yahaya, N. (2019). Synthesis and characterization of graphene oxide-molecularly imprinted polymer for Neopterin adsorption study. Journal of Polymer Research, 26(8), 184.

48.     Saidin, M. I., Sidik, S. M., & Ul-Hamid, A. (2024). Nickel-Zinc supported on mesoporous silica nanoparticles and its potential as a paracetamol sensor. Journal of Smart Sensors and Materials, 2(1), 4.

49.     Prabhu, S. N., Mukhopadhyay, S. C., Gooneratne, C. P., Davidson, A. S., & Liu, G. (2020). Molecularly imprinted polymer-based detection of creatinine towards smart sensing. Medical Devices & Sensors, 3(6), e10133.

50.     Prabhu, S. N., Gooneratne, C. P., & Mukhopadhyay, S. C. (2021). Development of MEMS sensor for detection of creatinine using MIP based approach – a tutorial paper. IEEE Sensors Journal, 21(20), 22170-22181.

51.     Mundinamani, S., & Rabinal, M. K. (2014). Cyclic voltammetric studies on the role of electrode, electrode surface modification and electrolyte solution of an electrochemical cell. IOSR Journal of Applied Chemistry, 7, 45-52.

52.     Lin, R., Huang, P., Ségalini, J., Largeot, C., Taberna, P. L., Chmiola, J., Gogotsi, Y., & Simon, P. (2009). Solvent effect on the ion adsorption from ionic liquid electrolyte into sub-nanometer carbon pores. Electrochimica Acta, 54(27), 7025-7032.

53.     Said, N. A. M., Awaludin, N., Salam, F., Razali, H., Ghazali, M. S., Talib, M. A. A., ... & Misman, S. N. (2023). Carboxylated multi-walled carbon nanotubes modified screen-printed electrodes for early detection of rice diseases using immunosensor approach. Journal of Smart Sensors and Materials, 1(1), 59-74.

54.     Salinas-Torres, D., Huerta, F., Montilla, F., & Morallón, E. (2011). Study on electroactive and electrocatalytic surfaces of single walled carbon nanotube-modified electrodes. Electrochimica Acta, 56(5), 2464-2470.

55.     Ahmad, K., Kumar, P., & Mobin, S. M. (2020). A highly sensitive and selective hydroquinone sensor based on a newly designed N-rGO/SrZrO3 composite. Nanoscale Advances, 2(1), 502-511.

56.     Singh, R. K., & Schechter, A. (2018). Electrochemical investigation of urea oxidation reaction on β Ni(OH)2 and Ni/Ni(OH)2. Electrochimica Acta, 278, 405-411.

57.     Sambasevam, K. P., Baharin, S. N. A., Zulkifli, A., Raoov, M., Asman, S., Mohamed, A. H., & Marimuthu, T. (2025). Factorial design assisted electrochemical detection of cypermethrin using molecularly imprinted polyaniline. Pure and Applied Chemistry, 97(8), 865-882.

58.     Qiu, X., Xu, X.-Y., Liang, Y., & Guo, H. (2018). The molecularly imprinted polymer supported by anodic alumina oxide nanotubes membrane for efficient recognition of chloropropanols in vegetable oils. Food Chemistry, 258, 295-300.

59.     Banurea, I. R., Sanjaya, A. R., Nizardo, N. M., & Ivandini, T. A. (2023). Molecularly imprinted polymer of p-amino thiophenol for a 3-monochloropropane-1,2-diol impedance-based sensor. Materials Chemistry and Physics, 301, 127613.

60.     Han, S., Ding, Y., Teng, F., Yao, A., & Leng, Q. (2021). Determination of chloropropanol with an imprinted electrochemical sensor based on multi-walled carbon nanotubes/metal–organic framework composites. RSC Advances, 11(30), 18468-18475.

61.     Martin, A. A., Fodjo, E. K., Eric-Simon, Z. V., Gu, Z., Yang, G., Albert, T., Kong, C., & Wang, H.-F. (2021). Cys-AgNPs modified gold electrode as an ultrasensitive electrochemical sensor for the detection of 3-chloropropane-1, 2-diol. Arabian Journal of Chemistry, 14(9), 103319.

62.     Rodríguez, L. C., Campańa, A. G., Barrero, F. A., Linares, C. J., & Ceba, M. R. (1995). Validation of an analytical instrumental method by standard addition methodology. Journal of AOAC International, 78(2), 471-476.

63.     Sambasevam, K. P., Mohamad, S., & Phang, S-W. (2017). Chemical sensor for hydrazine detection using polyaniline thin film. Malaysian Journal of Analytical Sciences, 21(4), 762-769.

64.     Saxberg, B. E., & Kowalski, B. R. (1979). Generalized standard addition method. Analytical Chemistry, 51(7), 1031-1038.