Malays.
J. Anal. Sci. Volume 30 Number 5 (2026): 1846
Research Article
Adsorption of allopurinol using
physically activated carbon derived from Leucaena leucocephala branches:
Optimisation and mass transfer modelling
Mohamad Hafiz Baharudin, Erniza Mohd Johan Jaya, Azrina Aziz and Mohd Azmier Ahmad*
School of Chemical
Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal,
Penang, Malaysia
*Corresponding author: chazmier@usm.my
Received: 1 March 2026; Revised: 26 May 2026; Accepted: 27
July 2026; Published: 31 October 2026
Abstract
Allopurinol (ALLO) is increasingly reported in water bodies because
conventional wastewater treatment often fails to eliminate it completely. This
work prepared an activated carbon from Leucaena leucocephala branches
(LLBAC) using a carbon dioxide (CO2) activation route and assessed
its ability to capture ALLO from water. Preparation variables were
systematically optimised through response surface methodology (RSM), while
Polymath mass transfer (PMT) modelling was applied to approximate the mass
transfer coefficient, km and adsorbent surface area, am.
The optimum synthesis conditions were 700 °C activation temperature and 1.30 h
activation time, producing a removal capacity of 71.41 mg g⁻¹ (actual
73.13 mg g⁻¹, error of 2.35%) with a carbon yield of 34.51% (actual
33.76%, error 2.22%). Batch adsorption experiments showed that maximum uptake
occurred at 30 °C and pH 6.7, reaching 73.13 mg g⁻¹. Equilibrium behaviour
followed the Freundlich model, indicating adsorption on energetically diverse
surfaces with possible multilayer formation. The theoretical Langmuir monolayer
capacity, Qm was 107.96 mg g⁻¹. Kinetic results were better
represented by the pseudo first order (PFO) model, suggesting that physical
interactions dominated the uptake process. The surface area estimated by the
Polymath model was 733.84 m² g⁻¹, closely agreeing with the measured
mesoporous area of 800.33 m² g⁻¹, corresponding to a small deviation of 8.31%.
Overall, the prepared LLBAC shows strong potential as an economical material
for ALLO removal in water treatment.
Keywords: Adsorption
process, physical activation, optimisation, isotherm, mass transfer
References
1. Zaini, Y. M. M., Purba, L. D. A., Abdullah, N., Yuzir, A., Iwamoto, K., and Mohamad, S. E. (2022). Removals of atenolol, gliclazide and prazosin using sequencing batch reactor. Materials Today: Proceedings, 65: 3007-3014.
2. Mohamad, F. M. Y., Abdullah, A. Z., and Ahmad, M. A. (2024). Amoxicillin adsorption from aqueous solution by Cu(II) modified lemon peel based activated carbon: Mass transfer simulation, surface area prediction and F-test on isotherm and kinetic models. Powder Technology, 438: 119589.
3. Gartenberg, A., Winkel, M., and Leonard, N. (2024). Spontaneous tumor lysis syndrome in a patient with chronic myeloid leukemia treated successfully with allopurinol. American Journal of Emergency Medicine, 78: 242.e1-242.e3.
4. Pol, K. H. v. d., Wever, K. E., Verbakel, M., Visseren, F. L. J., Cornel, J. H., and Rongen, G. A. (2021). Allopurinol to reduce cardiovascular morbidity and mortality: A systematic review and meta-analysis. PLoS ONE, 16(12): 1-19.
5. Saadh, M. J., Mirzaei, M., Ghnim, Z. S., Mosaddad, S. A., and Salem-Bekhit, M. M. (2024). Density functional theory analyses of an iron-doped nanocage for the adsorption of allopurinol drug towards the development of novel carriers. Computational and Theoretical Chemistry, 1237: 114664.
6. Funke, J., Prasse, C., Lütke Eversloh, C., and Ternes, T. A. (2015). Oxypurinol – A novel marker for wastewater contamination of the aquatic environment. Water Research, 74: 257-265.
7. Stamp, L. K., and Chapman, P. T. (2020). Allopurinol hypersensitivity: Pathogenesis and prevention. Best Practice and Research: Clinical Rheumatology, 34(4).
8. Hali, F., Chagraoui, H., Meftah, A., Marnissi, F., Chaabi, S., Chiheb, S., and Filali, H. (2023). Allopurinol induced severe cutaneous adverse reactions: Vigilance of prescription (31 cases). Revue Francaise d'Allergologie, 63(2).
9. Khir, N. H. M., Salleh, N. F. M., Ghafar, N. A., Shukri, N. M., and Jusoh, R. (2025). Preparation and characterization of modified rambutan peels for the removal of chromium(VI) and nickel(II) from aqueous solution: Environmental impact and optimization Malaysian Journal of Analytical Sciences, 29(1): 1292.
10. Firdaus, M. Y. M., Mohd Johan Jaya, E., and Ahmad, M. A. (2022). Single-stage microwave assisted coconut shell based activated carbon for removal of Zn(II) ions from aqueous solution – Optimization and batch studies. Arabian Journal of Chemistry, 15: 104011.
11. Yusop, M. F. M., Rashid, M. M., Alam, M. M., and Ahmad, M. A. (2026). Cu2+-surface-modified activated carbon from nutshells for enhanced metformin removal: Mass transfer simulation, attraction mechanism and F-test studies. Water, Air, & Soil Pollution, 237(9): 518.
12. Chen, J., Li, L., Shi, G., Yan, Y., Wang, Q., Yu, Z., Yan, L., and Yu, Y. (2025). Adsorption of chlorinated hydrocarbons by different kinds of soils: Kinetics, influencing factors, mechanism. Journal of Hazardous Materials Advances, 18: 100638.
13. Ramlee, D. A., Nordin, N. A., Rahman, N. A., and Bahruji, H. (2024). Removal of acetaminophen by using electrospun pan/sago lignin-based activated carbon nanofibers. Malaysian Journal of Analytical Sciences, 28(6): 1442 - 1457.
14. Gunasekaran, S., Liu, A. J. X., and Ng, S. L. (2024). Activated carbon/iron oxide composites with different weight ratios for acid orange 7 removal. Malaysian Journal of Analytical Sciences, 28(6): 1359 - 1373.
15. Mohamad, F. M. Y., Tamar Jaya, M. A., Idris, I., Abdullah, A. Z., and Ahmad, M. A. (2023). Optimization and mass transfer simulation of remazol brilliant blue R dye adsorption onto meranti wood based activated carbon. Arabian Journal of Chemistry, 16: 104683.
16. Ahammad, N. A., Yusop, M. F. M., Mohd Din, A. T., and Ahmad, M. A. (2021). Preparation of alpinia galanga stem based activated carbon via single-step microwave irradiation for cationic dye removal. Sains Malaysiana, 50(8): 2251-2269.
17. Ahmad, M. A., Yusop, M. F. M., Awang, S., Yahaya, N. K. E. M., Rasyid, M. A., and Hassan, H. (2021). Carbonization of sludge biomass of water treatment plant using continuous screw type conveyer pyrolyzer for methylene blue removal. IOP Conference Series: Earth and Environmental Science, 765: 012112.
18. Nasran, N. K. M., Firdaus, M. Y. M., Faizal, P. M. L. M., and Azmier, A. M. (2023). Alteration of Tecoma chip wood waste into microwave-irradiated activated carbon for amoxicillin removal: Optimization and batch studies. Arabian Journal of Chemistry, 16(10): 105110.
19. Kato-Noguchi, H., and Kurniadie, D. (2022). Allelopathy and Allelochemicals of Leucaenaleucocephala as an Invasive Plant Species. Plants, 11(13): 1672.
20. Badalamenti, E., Pasta, S., Sala, G., Catania, V., Quatrini, P., and La Mantia, T. J. I. J. o. P. B. (2020). The paradox of the alien plant Leucaena leucocephala subsp. glabrata (Rose) S. Zárate in Sicily: another threat for the native flora or a valuable resource? International Journal of Plant Biology, 11(1).
21. Sophia A, C., and Lima, E. C. (2018). Removal of emerging contaminants from the environment by adsorption. Ecotoxicology and Environmental Safety, 150: 1-17.
22. Perera, A. A. P. R., Madhushani, K. A. U., Kumar, A., and Gupta, R. K. (2023). Metal-organic frameworks for wastewater treatment: Recent developments, challenges, and future prospects. Chemosphere, 339: 139713.
23. Ranjan Rout, D., and Mohan Jena, H. (2022). Synthesis of novel reduced graphene oxide decorated β-cyclodextrin epichlorohydrin composite and its application for Cr(VI) removal: Batch and fixed-bed studies. Separation and Purification Technology, 278.
24. Rout, D. R., Jena, H. M., Baigenzhenov, O., and Hosseini-Bandegharaei, A. (2023). Graphene-based materials for effective adsorption of organic and inorganic pollutants: A critical and comprehensive review. Science of The Total Environment, 863: 160871.
25. Capodaglio, A. G., Bojanowska-Czajka, A., and Trojanowicz, M. (2018). Comparison of different advanced degradation processes for the removal of the pharmaceutical compounds diclofenac and carbamazepine from liquid solutions. Environmental Science and Pollution Research, 25(28): 27704-27723.
26. Taoufik, N., Boumya, W., Achak, M., Sillanpää, M., and Barka, N. (2021). Comparative overview of advanced oxidation processes and biological approaches for the removal pharmaceuticals. Journal of Environmental Management, 288: 112404.
27. Obotey Ezugbe, E., and Rathilal, S. (2020). Membrane technologies in wastewater treatment: A review. Membranes (Basel), 10(5): 89.
28. Firdaus, M. Y. M., Rashid, M. M., Alam, M. M., and Ahmad, M. A. (2025). Enhanced Cd2+ removal via deprotonated-mango trunk functionalized carbon: Optimization and F-test for linear and non-linear isotherm and kinetic models. Chemical Engineering Research and Design, 220: 96-116.
29. Daouda, M. M. A., Akowanou, A. V. O., Mahunon, S. E. R., Adjinda, C. K., Aina, M. P., and Drogui, P. (2021). Optimal removal of diclofenac and amoxicillin by activated carbon prepared from coconut shell through response surface methodology. South African Journal of Chemical Engineering, 38(1): 78-89.
30. Yusop, M. F. M., Baharudin, M. H., Rashid, M. M., Alam, M. M., and Ahmad, M. A. (2025). Amoxicillin adsorption onto oil palm trunk-derived activated carbon: synthesis optimization, modelling of mass transfer and ultrasonic regeneration. Journal of Chemical Technology & Biotechnology, 100(6): 1310-1327.
31. Yusop, M. F. M., Mohd Johan Jaya, E., Mohd Din, A. T., Bello, O. S., and Ahmad, M. A. (2022). Single-stage optimized microwave-induced activated carbon from coconut shell for cadmium adsorption. Chemical Engineering & Technology, 45(11): 1943-1951.
32. Angel, L., Villot, A., Rodriguez Susa, M., Plazas-Tuttle, J., Andres, Y., and Gerente, C. (2025). Optimizing activated carbon production from chontaduro seeds via physical activation with steam for ibuprofen removal: A factorial design and multi-attribute utility theory approach. Journal of Water Process Engineering, 70: 107020.
33. Mirzaee, S. A., Bayati, B., Valizadeh, M. R., Gomes, H. T., and Noorimotlagh, Z. (2021). Adsorption of diclofenac on mesoporous activated carbons: Physical and chemical activation, modeling with genetic programming and molecular dynamic simulation. Chemical Engineering Research and Design, 167: 116-128.
34. Inglezakis, V. J., Balsamo, M., and Montagnaro, F. (2020). Liquid–solid mass transfer in adsorption systems—an overlooked resistance? Industrial & Engineering Chemistry Research, 59(50): 22007-22016.
35. Mohd Ramli, M. R., Shoparwe, N. F., and Ahmad, M. A. (2023). Methylene blue removal using activated carbon adsorbent from Jengkol peel: Kinetic and mass transfer studies. Arabian Journal for Science and Engineering, 48(7): 8585-8594.
36. Firdaus, M. Y. M., Rashid, M. M., Alam, M. M., and Ahmad, M. A. (2025). Copper-modified surface of orange peel-derived activated carbon for amoxicillin removal: mass transfer simulation, attraction mechanism, and regeneration studies. Arabian Journal for Science and Engineering.
37. Langmuir, I. (1918). The adsorption of gases on plane surfaces of glass, mica and platinum. Journal of the American Chemical Society, 40(9): 1361-1403.
38. Freundlich, H. (1906). Over the adsorption in solution. Journal of Physical Chemistry, 57(385471): 1100-1107.
39. Tempkin, M., and Pyzhev, V. (1940). Kinetics of ammonia synthesis on promoted iron catalyst. Acta Physicochimica URSS, 12(1): 327.
40. Firdaus, M. Y. M., Rashid, M. M., Alam, M. M., and Ahmad, M. A. (2025). Synthesis of deprotonated grape stem functionalized carbon for boosted Cu2+ adsorption – optimization, interaction mechanism, and F-test analysis. Microchemical Journal, 218: 115795.
41. Revellame, E. D., Fortela, D. L., Sharp, W., Hernandez, R., and Zappi, M. E. (2020). Adsorption kinetic modeling using pseudo-first order and pseudo-second order rate laws: A review. Cleaner Engineering and Technology, 1: 100032.
42. Mohamad, F. M. Y., Rashid, M. M., Alam, M. M., and Ahmad, M. A. (2026). Synthesis of deprotonated-langsat peel activated carbon for improved Pb2+ adsorption: Optimization and F-test for isotherm and kinetic models. Diamond and Related Materials, 165: 113650.
43. Weber, W. J., and Morris, J. C. (1963). Kinetics of adsorption on carbon from solution. Journal of the Sanitary Engineering Division, 89(2): 31-59.
44. Boyd, G. E., Adamson, A. W., and Myers, L. S., Jr. (1947). The exchange adsorption of ions from aqueous solutions by organic zeolites. II. Kinetics. Journal of the American Chemical Society, 69(11): 2836-2848.
45. Lima, E. C., Hosseini-Bandegharaei, A., Moreno-Piraján, J. C., and Anastopoulos, I. (2019). A critical review of the estimation of the thermodynamic parameters on adsorption equilibria. Wrong use of equilibrium constant in the Van't Hoof equation for calculation of thermodynamic parameters of adsorption. Journal of Molecular Liquids, 273: 425-434.
46. Beyan, S. M., Prabhu, S. V., Sissay, T. T., and Getahun, A. A. (2021). Sugarcane bagasse based activated carbon preparation and its adsorption efficacy on removal of BOD and COD from textile effluents: RSM based modeling, optimization and kinetic aspects. Bioresource Technology Reports, 14: 100664.
47. Mahari, W. A. W., Zainuddin, N. F., Nik, W. M. N. W., Chong, C. T., and Lam, S. S. (2016). Pyrolysis recovery of waste shipping oil using microwave heating. Energies, 9(10): 780.
48. Weldekidan, H., Patel, H., Mohanty, A., and Misra, M. (2024). Synthesis of porous and activated carbon from lemon peel waste for CO2 adsorption. Carbon Capture Science & Technology, 10: 100149.
49. Mohamad, F. M. Y., Rashid, M. M., Alam, M. M., and Ahmad, M. A. (2025). Copper metal-functionalized carbon from rattan waste via microwave pyrolysis for enhanced chloramphenicol removal: Optimization and F-test study. Particuology, 100: 196-213.
50. Nguyen, D. T., Tran, H. N., Juang, R.-S., Dat, N. D., Tomul, F., Ivanets, A., Woo, S. H., Hosseini-Bandegharaei, A., Nguyen, V. P., . . . Chao, H.-P. (2020). Adsorption process and mechanism of acetaminophen onto commercial activated carbon. Journal of Environmental Chemical Engineering, 8(6): 104408.
51. Shahrokhi-Shahraki, R., Benally, C., El-Din, M. G., and Park, J. (2021). High efficiency removal of heavy metals using tire-derived activated carbon vs commercial activated carbon: Insights into the adsorption mechanisms. Chemosphere, 264: 128455.
52. Sun, Y., Wang, Z., Zhang, S., Liu, C., and Xu, Y. (2024). Preparation of composites with MgAl-LDH-modified commercial activated carbon for the quick removal of Cr(VI) from aqueous solutions. Environmental Science and Pollution Research, 31(28): 41032-41045.
53. Kuśmierek, K., Dąbek, L., and Świątkowski, A. (2025). The influence of the shape and grain size of commercial activated carbons on their sorption efficiency towards organic water pollutants. Desalination and Water Treatment, 321: 100996.
54. Wei, X., Huang, S., Yang, J., Liu, P., Li, X., Wu, Y., and Wu, S. (2023). Adsorption of phenol from aqueous solution on activated carbons prepared from antibiotic mycelial residues and traditional biomass. Fuel Processing Technology, 242: 107663.
55. Veysi, O., Elif, O., Davut, B., and Ahmet, O. (2010). Simultaneous removal of indomethacine, papaverine and allopurinol from aqueous solution by using submerged aquatic plant Nasturtium officinale. Asian Journal of Chemistry, 22(3): 2081-2089.
56. Wang, J., and Guo, X. (2023). Adsorption kinetics and isotherm models of heavy metals by various adsorbents: An overview. Critical Reviews in Environmental Science and Technology, 53(21): 1837-1865.
57. Aziz, A., Mohamad Yusop, M. F., and Ahmad, M. A. (2024). Harnessing microwave energy to transform Nephelium lappaceum L. peel into activated carbon for chloramphenicol eradication in aqueous solutions. Materials Chemistry and Physics, 318: 129311.
58. Yusop, M. F. M., Rashid, M. M., Alam, M. M., and Ahmad, M. A. (2026). Optimized copper-functionalized carbon from Lansium parasiticum trunk for chloramphenicol removal from aqueous solution. International Journal of Environmental Science and Technology, 23(4): 306.
59. Mohamad, F. M. Y., Abdullah, A. Z., and Ahmad, M. A. (2023). Adsorption of remazol brilliant blue R dye onto jackfruit peel based activated carbon: Optimization and simulation for mass transfer and surface area prediction. Inorganic Chemistry Communications, 158: 111721.
60. Yusop, M. F. M., Ahmada, M. A., Roslia, N. A., Gonawana, F. N., and Abdullahb, S. J. (2021). Scavenging malachite green dye from aqueous solution using durian peel based activated carbon. Malaysian Journal of Fundamental and Applied Sciences, 17(1): 95-103.
61. El Jery, A., Alawamleh, H. S. K., Sami, M. H., Abbas, H. A., Sammen, S. S., Ahsan, A., Imteaz, M. A., Shanableh, A., Shafiquzzaman, M., and Al-Ansari, N. (2024). Isotherms, kinetics and thermodynamic mechanism of methylene blue dye adsorption on synthesized activated carbon. Scientific Reports, 14(1): 970.
62. Firdaus, M. Y. M., Nasehir Khan, M. N., Zakaria, R., Abdullah, A. Z., and Ahmad, M. A. Mass transfer simulation on remazol brilliant blue R dye adsorption by optimized teak wood based activated carbon. Arabian Journal of Chemistry, 16: 104780.