Malays. J. Anal. Sci. Volume 30 Number 5 (2026): 1818

 

Research Article

 

Characterization and morphology of PdNiCo trimetallic MOF-derived porous carbon catalyst at different pyrolysis temperatures

 

Najihah Syahbudin1, Muhammad Shafie Norhisham1, Norliza Dzakaria1,2*, Azizul Hakim Lahuri3, Wan Nor Roslam Wan Isahak4, Nurul Auni Zainal Abidin1, Mohd Lokman Ibrahim5, and Mohamad Azuwa Mohamed6

 

1School of Chemistry and Environment, Faculty of Applied Sciences, Universiti Teknologi MARA(UiTM), Cawangan Negeri Sembilan, Kampus Kuala Pilah, 72000 Kuala Pilah, Negeri Sembilan, Malaysia.

2Advanced Material for Environmental Remediation (AMER), Universiti Teknologi MARA(UiTM), Cawangan Negeri Sembilan, Kampus Kuala Pilah, 72000 Kuala Pilah, Negeri Sembilan, Malaysia.

3Department of Science and Technology, Universiti Putra Malaysia Sarawak, Nyabau Road, P.O Box 396, 97008 Bintulu, Sarawak, Malaysia.

4Department of Chemical and Process Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor, Malaysia.

5School of Chemistry and Environment, Faculty of Applied Sciences, Universiti Teknologi MARA (UiTM), 40450 Shah Alam, Selangor, Malaysia.

6Department of Chemical Sciences, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia.

 

*Corresponding author: norliza864@uitm.edu.my

 

Received: 14 February 2026; Revised: 8 July 2026; Accepted: 27 July 2026; Published: 31 October 2026

 

Abstract

Efficient trimetallic catalysts require control of alloy formation, dispersion, and porous supports to maximize active-site accessibility for sustainable hydrogen generation. However, the influence of pyrolysis temperature on structural evolution of MOF‑derived PdNiCo catalysts is not well understood. This study determines how pyrolysis temperature (500, 700, 900 °C) affects the structural, morphological, and textural properties of equimolar PdNiCo (1:1:1) supported on MOF‑derived porous carbon and links these changes to catalytic performance for formic acid dehydrogenation. PdNiCo‑MOF precursors were pyrolyzed at 500, 700, and 900 °C under 20% H2/Ar. Materials were characterized by XRD, FESEM‑EDX, CHNS, and N2 adsorption‑desorption analysis using the Brunauer-Emmett-Teller (BET) method. Catalytic activity and apparent activation energy were evaluated via batch formic acid dehydrogenation experiments. Properties were found to vary non‑monotonically with temperature. XRD confirmed enhanced crystallinity and possible alloy formation at 900 °C. FESEM revealed particle coalescence at 700 °C and smaller primary particles (~146.6 nm) at 900 °C, while EDX confirmed Pd, Ni, and Co in all catalysts. CHNS analysis showed increased carbon content (12.20-14.53 wt%) and decreased nitrogen and hydrogen contents with increasing pyrolysis temperature, indicating progressive carbonization. PdNiCo/PC‑900 showed the best combination of crystallinity and porosity with well‑defined fcc metallic phases, highest BET surface area (40.92 m2 g‑1) and pore volume (0.117 cm3 g‑1), small primary particles (~146.6 nm), and lowest activation energy (≈19.3 kJ mol‑1) and TOF ≈ 104.48 h‑1, yielding the highest catalytic rates. PdNiCo/PC‑700 represented a sintering window with severe particle coalescence, structural densification, and the lowest surface area (16.77 m2 g‑1). PdNiCo/PC‑500 exhibited incomplete MOF decomposition and limited alloy crystallinity. Optimal performance requires balancing alloy crystallinity, controlled agglomeration, and hierarchical porosity. PdNiCo/PC‑900 is hence identified as the preferred pyrolysis condition for producing high‑performance PdNiCo trimetallic catalysts for sustainable hydrogen production.

 

Keywords: metal organic frameworks, trimetallic, pyrolysis temperature, porous carbon

 


References

1.        Al-Aqtash, O., Sápi, A., Farkas, F., Basheer, H. S., Kukovecz, Á., & Kónya, Z. (2025). Enhanced performance and cost-effectiveness of Pd-based catalysts with Cu, Ni, and Co promoters for CO and NOx conversion in flue gas emission. Atmospheric Pollution Research, 16, 102579.

2.        Bumagin, N. A. (2022). Reusable proline-containing bimetallic Pd–Ni(Co, Cu, Fe)–Pro/Al₂O₃ catalysts for Suzuki reaction in water. Russian Journal of General Chemistry, 92, 832–840.

3.        Ding, J., Wang, H. F., Yang, X., Ju, W., Shen, K., Chen, L., & Li, Y. (2023). A Janus heteroatom-doped carbon electrocatalyst for hydrazine oxidation. National Science Review, 10, 231.

4.        Castillo-Blas, C., Chester, A. M., Keen, D. A., & Bennett, T. D. (2024). Thermally activated structural phase transitions and processes in metal-organic frameworks. Chemical Society Reviews, 53(7), 3606-3629.

5.        Hernández-Ferrer, J., Gracia-Martín, M., Benito, A. M., Maser, W. K., & García-Bordejé, E. (2023). Effect of temperature and presence of minor amount of metal on porous carbon materials derived from ZIF8 pyrolysis for electrocatalysis. Catalysis Today, 423, 024.

6.        Hintz, H., & Wuttke, S. (2014). Supporting information: Postsynthetic modification of an amino-tagged MOF using peptide coupling reagents: A comparative study. Chemical communications, 50(78), 11472-11475.

7.        Wang, Y., & Zhang, Q. (2023). Temperature-dependent tailoring of the pore structure based on MOF-derived carbon electrodes for electrochemical capacitors. RSC Advances, 13, 18145–18155.

8.        Landström, K. N., Nambi, A., Kaiser, A., & Akhtar, F. (2023). Inducing hierarchical pores in nano-MOFs for efficient gas separation. RSC Advances, 13, 16039–16046.

9.        Yin, P., Hu, S., Qian, K., Wei, Z., Zhang, L. L., Lin, Y., Huang, W., Xiong, H., Li, W. X., & Liang, H. W. (2021). Quantification of critical particle distance for mitigating catalyst sintering. Nature Communications, 12, 251162.

10.     Yang, S. J., Kim, T., Im, J. H., Kim, Y. S., Lee, K., Jung, H., & Park, C. R. (2012). MOF-derived hierarchically porous carbon with exceptional porosity and hydrogen storage capacity. Chemistry of Materials, 24, 464–470.

11.     Huang, Y., Chen, Y., Xu, M., Ly, A., Gili, A., Murphy, E., Asset, T., Liu, Y., De Andrade, V., Segre, C. U., Deriy, A. L., De Carlo, F., Kunz, M., Gurlo, A., Pan, X., Atanassov, P., & Zenyuk, I. V. (2023). Catalysts by pyrolysis: Transforming metal-organic frameworks (MOFs) precursors into metal-nitrogen-carbon (M-N-C) materials. Materials Today, 69, 66-78.