Malays. J. Anal. Sci. Volume 30 Number 5 (2026): 1813

 

Research Article

 

The potential of eggshell waste as an alternative filler in natural rubber composites 

 

Abdulhakim Masa1*, Chananchida Janpong1, Anchuleekorn Kaomodjod1, Sasipim Chatarat1, Ruedee Jaratrotkamjorn1, and Siriwat Soontaranon2

 

1Rubber Engineering Program, Department of Interdisciplinary Engineering, Faculty of Engineering, Prince of Songkla University, Hat Yai, Songkla 90110, Thailand

2Synchrotron Light Research Institute, Muang District, Nakhon Ratchasima 30000, Thailand

 

*Corresponding author: abdulhakim.m@psu.ac.th

 

Received: 26 December 2025; Revised: 18 April 2026; Accepted: 18 August 2026; Published: 31 October 2026

 

Abstract

This study assesses the applicability of eggshell waste powder as a calcium carbonate (CaCO3) filler in natural rubber (NR) composites. A composite containing commercial-grade CaCO3 was also prepared for reference. The effects of eggshell powder particle size on the NR's morphological, mechanical, thermomechanical, swelling, and processing-ability features were examined. The inclusion of eggshell powder improved the rubber composites' curing torque, swelling resistance, crosslink density, and modulus at different stresses when compared to an unfilled control sample, but it reduced their tensile strength, extensibility, and thermomechanical characteristics independent of particle size. In contrast, the commercial-grade CaCO3 improved all properties due to greater interaction with the rubber matrix compared to the eggshell powder (ESP). The ability of NR to crystallize during stretching was reduced by adding CaCO3 in all cases, so these fillers retard the strain-induced crystallization. The tensile strength of NR composites filled with ESP 132 decreased by 7.23% compared to that filled with commercial-grade CaCO3, while a greater reduction of 33.87% was observed for the composite containing ESP 300. The mechanical properties remained acceptable, with tensile strength ~ 17.83 MPa and elongation at break ~ 394%, even though the inclusion of eggshell powder led to poor thermal properties. This happened when the eggshell powder with a particle size of 132 ΅m was utilized. Therefore, it would be practical to use eggshell waste as a filler in rubber-based goods. This bio-filler has substantial benefits in rubber formulations because of its sustainability and availability.

 

Keywords: natural rubber, composites, eggshell waste, calcium carbonate, filler

 


References

1.        El Mogy, S. A., Darwish, N. A. and Awad, A. (2020). Comparative study of the cure characteristics and mechanical properties of natural rubber filled with different calcium carbonate resources. Journal of Vinyl and Additive Technology, 26 (3): 309 – 315.

2.        Ramesh, M., Rajeshkumar, L. N., Srinivasan, N., Kumar, D. V. and Balaji, D. (2022). Influence of filler material on properties of fiber-reinforced polymer composites: a review. e-Polymers, 22 (1): 898 – 916.

3.        Sowinska-Baranowska, A. and Maciejewska, M. (2023). Potential utilization of ground eggshells as a biofiller for natural rubber biocomposites. Materials, 16 (8): 2988.

4.        Hayeemasae, N., Soontaranon, S. and Masa, A. (2024). Comparative investigation of nano-sized silica and micrometer-sized calcium carbonate on structure and properties of natural rubber composites. Polymers, 16 (8): 1051.

5.        Damircheli, M., MajidiRad, A. and Asmatulu, R. (2025). Calcium carbonate nanoparticle-reinforced rubber: enhancing dynamic mechanical performance and thermal properties. Journal of Materials Research and Technology, 36: 326–336.

6.        Intharapat, P., Kongnoo, A. and Kateungngan, K. (2013). The potential of chicken eggshell waste as a bio-filler filled epoxidized natural rubber (ENR) composite and its properties. Journal of Polymers and the Environment, 21 (1): 245–258.

7.        Bashir, A. S., Manusamy, Y., Chew, T. L., Ismail, H. and Ramasamy, S. (2017). Mechanical, thermal, and morphological properties of eggshell powder-filled natural rubber latex foam. Journal of Vinyl and Additive Technology, 23 91): 3 – 12.

8.        Munusamy, Y. and Kchaou, M. (2023). Usage of eggshell as potential bio-filler for acrylonitrile butadiene rubber (NBR) latex film for glove applications. Ain Shams Engineering Journal, 14 (11): 102512.

9.        Kowshik, S., Sharma, S., Rao, S., Shettar, M. and Hiremath, P. (2023). Mechanical properties of post-cured eggshell-filled glass-fibre-reinforced polymer composites. Journal of Composites Science, 7 (2): 49.

10.   Tangboriboon, N., Pannangpetch, W., Aranyik, K., Petcharoen, K. and Sirivat, A. (2015). Embedded eggshells as a bio-filler in natural rubber for thermal insulation composite foams. Progress in Rubber, Plastics and Recycling Technology, 31 93): 189 – 205.

11.   Bhagavatheswaran, E. S., Das, A., Rastin, H., Saeidi, Hoda, Jafari, S. H., Vahabi, H., Najafi, F., Khonakdar, H. A., Formela, K., Jouyandeh, M., Zarrintaj, P. and Saeb, M. R. (2019). The taste of waste: the edge of eggshell over calcium carbonate in acrylonitrile butadiene rubber. Journal of Polymers and the Environment, 27: 2478 – 2489.

12.   Barrera, C. S. and Cornish, K. (2015). Novel mineral and organic materials from agro-industrial residues as fillers for natural rubber. Journal of Polymers and the Environment, 23 (4): 437 – 448.

13.   Manaila, E., Craciun, G., Ighigeanu, D., Lungu, I. B., Dumitru Grivei, M. D. and Stelescu, M. D. (2022). Degradation by electron beam irradiation of some composites based on natural rubber reinforced with mineral and organic fillers. International Journal of Molecular Sciences, 23(13), 6925.

14.   Lumlong, S., Pungpo, P., Khamsri, B., Saenglam, I. and Kongkaew, C. (2018). Study the effect of calcium carbonate from eggshell as a filler in natural rubber. International Journal of Advanced Science, Engineering and Technology, 6 (1): 12 – 15.

15.   Flory, P. J. and Rehner, J. Jr. (1943). Statistical mechanics of crosslinked polymer networks I. Rubberlike elasticity. Journal of Chemical Physics, 11 (11): 512 – 520.

16.   Musto, S., Barbera, V., Cipolletti, V., Citterio, A. and Galimberti, M. (2017). Master curves for the sulphur assisted crosslinking reaction of natural rubber in the presence of nano- and nano-structured sp² carbon allotropes. eXPRESS Polymer Letters, 11 (6): 435 – 448.

17.   Lorenz, O. and Parks, C. R. (1961). The crosslinking efficiency of some vulcanizing agents in natural rubber. Journal of Polymer Science, 50 (154): 29 9– 312.

18.   Swapna, V. P., Stephen, R., Greeshma, T., Sharan Dev, C. and Sreekala, M. S. (2016). Mechanical and swelling behavior of green nanocomposites of natural rubber latex and tubular shaped halloysite nanoclay. Polymer Composites, 37 (2): 602 – 611.

19.   Hayeemasae, N., Soontaranon, S. and Masa, A. (2024). Influences of compatibilizer type and loading on properties of phenolic resin-crosslinked natural rubber composites filled with sepiolite. eXPRESS Polymer Letters, 18 (11): 1135 – 1148.

20.   Vennemann, N. and Fremuth, K. (2021). TSSR: a versatile test method for elastomers and TPEs. Rubber Plastics News, July 12: 14 – 17.

21.   Chatterjee, T., Vennemann, N. and Naskar, K. (2018). Temperature scanning stress relaxation measurements: a unique perspective for evaluation of the thermomechanical behavior of shape memory polymer blends. Journal of Applied Polymer Science, 135 (2): 45680.

22.   Pongdong, W., Kummerlowe, C., Vennemann, N., Thitithammawong, A. and Nakason, C. (2018). A comparative study of rice husk ash and siliceous earth as reinforcing fillers in epoxidized natural rubber composites. Polymer Composites, 39 (2): 414 – 426.

23.   Rabiei, S. and Shojaei, A. (2016). Vulcanization kinetics and reversion behavior of natural rubber/styrene-butadiene rubber blend filled with nanodiamond–the role of sulfur curing system. European Polymer Journal, 81: 98 – 113.

24.   Hayeemasae, N., Adair, A. and Masa, A. (2022). Comparative study on viscosities, stress relaxation, curing and mechanical properties of sepiolite and silica filled natural rubber composites. Malaysian Journal of Analytical Sciences, 26, 176-190.

25.   Wang, P. Y., Chen, Y. and Qian, H. L. (2007). Vulcanization kinetics of low-protein natural rubber with use of a vulcameter. Journal of Applied Polymer Science, 105 (6): 3255 – 3259.

26.   Masa, A., Krem-ae, A., Ismail, H. and Hayeemasae, N. (2020). Possible use of sepiolite as alternative filler for natural rubber. Materials Research, 23: e20200100.

27.   Chu, Q., Tian, X., Bian, H. and Wang, C. (2025). Optimization of mechanical and dynamic properties of tread rubber using fumed silica and hydration processing. Polymers, 17 (6): 714.

28.   Masa, A., Soontaranon, S. and Hayeemasae, N. (2020). Influence of sulfur/accelerator ratio on tensile properties and structural inhomogeneity of natural rubber. Polymer Korea, 44 (4): 519–526.

29.   Hayeemasae, N., Waesateh, K., Soontaranon, S. and Masa, A. (2022). Effect of vulcanization systems and crosslink density on tensile properties and network structure of natural rubber. Jurnal Teknologi, 84 (6): 181–187.

30.   Salgueiro, W., Marzocca, A., Somoza, A., Consolati, G., Cerveny, S., Quasso, F. and Goyanes, S. (2004). Dependence of the network structure of cured styrene butadiene rubber on the sulphur content. Polymer, 45 (17): 6037 – 6044.

31.   Thomas, D., Janardhanan, C. and Sebastian, M. T. (2011). Mechanically flexible butyl rubber–SrTiO₃ composite dielectrics for microwave applications. International Journal of Applied Ceramic Technology, 8 (5): 1099–1107.

32.   Ismail, H., Omar, N. and Othman, N. (2011). Effect of carbon black loading on curing characteristics and mechanical properties of waste tyre dust/carbon black hybrid filler filled natural rubber compounds. Journal of Applied Polymer Science, 121 (2): 1143–1150.

33.   Inphonlek, S., Bureewong, N., Kotchapradit, S., Ruksakulpiwat, Y. and Ruksakulpiwat, C. (2025). Synergistic effects of hybrid bio-fillers and modified natural rubber on natural rubber composite properties. Polymers, 17 (5): 632.

34.   Poompradub, S., Tosaka, M., Kohjiya, S., Ikeda, Y., Toki, S., Sics, I. and Hsiao, B. S. (2005). Mechanism of strain-induced crystallization in filled and unfilled natural rubber vulcanizates. Journal of Applied Physics, 97 (10): 103529.

35.   Wongvasana, B., Thongnuanchan, B., Masa, A., Saito, H., Sakai, T. and Lopattananon, N. (2023). Reinforcement behavior of chemically unmodified cellulose nanofiber in natural rubber nanocomposites. Polymers, 15 (5): 1274.

36.   Masa, A., Hayeemasae, N., Soontaranon, S., Pisal, M. H. M. and Rasidi, M. S. M. (2021). Effect of stretching rate on tensile response and crystallization behavior of crosslinked natural rubber. Malaysian Journal of Fundamental and Applied Sciences, 17 (3): 217 – 225.

37.   Hayeemasae, N., Soontaranon, S. and Masa, A. (2023). Influence of different vulcanizing agents on structures and properties of sepiolite-filled natural rubber composites. eXPRESS Polymer Letters, 17 (2): 181–195.

38.   Promsung, R., Nakaramontri, Y., Uthaipan, N., Kummerlowe, C., Johns, J., Vennemann, N. and Kalkornsurapranee, E. (2021). Effects of protein contents in different natural rubber latex forms on the properties of natural rubber vulcanized with glutaraldehyde. eXPRESS Polymer Letters, 15 (4): 308 – 318.

39.   Nakaramontri, Y., Kummerlowe, C., Vennemann, N., Wisunthorn, S., Pichaiyut, S. and Nakason, C. (2018). Effect of bis(triethoxysilylpropyl)tetrasulfide (TESPT) on properties of carbon nanotubes and conductive carbon black hybrid filler filled natural rubber nanocomposites. eXPRESS Polymer Letters, 12 (10): 867–884.

40.   Hayeemasae, N., Fathurrohman, M. I. and Masa, A. (2023). Effects of maleic anhydride content on thermomechanical and mechanical properties of maleated natural rubber. Polymer Korea, 47 (5): 565 – 573.

41.   Pongdong, W., Kummerlowe, C., Vennemann, N., Thitithammawong, A. and Nakason, C. (2018). A comparative investigation of rice husk ash and siliceous earth as reinforcing fillers in dynamically cured blends of epoxidized natural rubber (ENR) and thermoplastic polyurethane (TPU). Journal of Polymers and the Environment, 26 (3): 1145 – 1159.